How to Identify Faults For Washing Machines Or Dishwashers Before You Call an Engineer

I am a washing machine, dishwasher and tumble dryer engineer, and my customers are usually pretty good at explaining what the fault is. However, a few extra tips from an engineers point of view might suffice to help you as a Customer to help me trace a fault quickly. It could be very helpful if as much information as possible is given to the build-up leading up to when the machine started to go wrong. If the fault description is not quite right, its easy to start at the wrong end of the problem and waste a lot of time.(a classic case of going round the moon to get to your…..well I’ll leave it there!). Sometimes its difficult because you switch it on and walk away and you don’t notice anything until it goes obviously horribly wrong. Take time out and observe exactly what’s happening and at what point its happening.

Before you call an engineer there are some simple checks that you can do, which not only can help an engineer if you call one but, you never know, you might avoid calling him out at all lg dishwasher repair los angeles. There are the obvious faults, of cause. If the machine is full of water and not draining, (also, this produces another symptom, the machine will not spin the clothes at the end of the wash programme, its not the spin function that’s wrong its the fact that there’s water still in the drum which will stop it spinning). Try this, some machines have a drain only function, this eliminates any noise from something else happening, like the drum turning for instance, if there isn’t a drain only function select a spin and there should be a minute or two before the drum starts turning meanwhile you should hear the sound of the drain pump churning. Can you hear anything? No! then the drain pumps not working. If its a Yes! then there is a blockage somewhere.

The other obvious one is if nothing happens at all when you switch on, some machines have some form of ‘mains on’ indicator light, if its not on when you push the mains switch on then there is no power going to the machine. Check the mains electric socket that the machine uses, plug a table lamp into the socket, and see if you’ve got power to the machine. If not, check the fuse in the plug, sounds obvious, but its worth checking. If you’ve got power to the machine then its possibly the door switch on the door of the machine, so you would call an engineer for that.

If its being incredibly naughty and spilling water all over the floor (then you’ve got the Deluxe model there cleans your floor as well!). Turn everything off like the water taps (usually under the sink) to the machine and unplug the mains plug, then call someone. That goes for the machine tripping safety switches or blowing electric mains fuses as well. What I mean is those faults that the machine is working but then stops or doesn’t do something that it should. Try a few things out first, does the timer stop at the same point in the cycle? On electo-mechanical timer units (you can identify this type as the dial you set your programme with and clicks on a detent mechanism as you turn it around, and turns around as the wash programme advances). If it stops or the machine just carries on indefinitely doing the same function with the timer just sticking in the same place or you have to click the timer on one click and the machine carries on. Before you do that though, mark it with a pencil on the dial and on the corresponding part of the panel. Then the engineer can see the exact point the fault is occurring. This type of fault can indicate a heater or timer problem.

However, due to modern technical advances, mechanical timers are being replaced by electronic control devices, so you can’t see at what point the programme is. Although some have a programme timer LED display, make a note of the time the display has when the fault occurs (or anything in the display for that matter) and also the programme you are using. Some of them cough up error codes on its LED display, these can be listed, to a limited degree in the operators handbook but they are not usually very comprehensive. The only thing you can do here (again first make a note of which programme the machine went wrong on) is to start a programme again, this time though try a ‘Quick’ or the shortest wash programme there is on a washing machine, if its a dishwasher again try a ‘Quick’ programme if its got one. Don’t try the ‘Rinse’ programme because that doesn’t heat the water and it might be a heating fault. Time how long into the cycle it goes before it stops or goes wrong or sometimes if it doesn’t go wrong at all. To an engineer this can help to eliminate a few things. If you think it may be the water is not going into the machine on a washing machine or dishwasher, just loosen off the the hose connection into the back of the machine (don’t disconnect it completely) and see if the water is coming through. Unfortunately, it does require heaving the the machine out to get at the back to do this. If it isn’t check the shut off valve hasn’t been turned off. Surprisingly, and not altogether uncommon, the valve to the machine can be turned off, for instance if you have just had a plumber round to do a job (or hubby), perhaps some work under the sink and his forgotten to turn the tap back on again.

If you have done all this, you’ve done two things. You have eliminated any possibility that there was something very simple and you can possibly fix it yourself, which has saved you an engineers call. And also the possibility if it turns out not to be the machine and its a house wiring problem, no power from the mains socket for instance, in which case you call an electrician. Or if its a water problem you call a plumber. And secondly, if you do call one you can explain to the engineer your diagnosis, and he’ll make you a cup of tea!

Leave a Comment